CAN J1939 Expansion Module for iX and EXTER/E1000 Operator Panels (MAEN962/MADE962)

The expansion module is used for the operator panel to communicate via CAN J1939. The correct driver must be installed in the operator panel.

• CAN_J1939_EM_MADE962_German.pdf
• CAN_J1939_EM_MAEN962_English.pdf

CAB15: CANopen Adapter. CIMREX and EXTER / E- and E1000 Series. RS422

The adapter is easily mounted in the RS422 interface on the operator panel . Should the installation space limit the possibility to plug in the adapter directly on the back of the operator panel, simply use the optional bracket and connector cable to mount the adapter in a more convenient location (up to 1.5 meters from the panel).

• 4350K.pdf
• 4350s1.pdf

CAB14: Matsushita FPO/M/2/2SH to CIMREX and EXTER / E- and E1000 Series with CAB12. RS232

• 4790S.pdf

CAB12: 9-Pin Male/Female D-Sub Adapter. EXTER / E1000 Series to CIMREX / E- Series Cables RS232

• 3356s.pdf

CAB11: MPI Adapter between Siemens S7 and CIMREX and EXTER / E- and E1000 Series MPI to RS232

CAB11 to CIMREX: Use cable assembly CAB5
CAB11 to EXTER: Use cable assembly CAB5 and CAB12 adapter in EXTER connector
Overview panels via MPI: See drawing 5409K
Outline CAB11: See drawing 3359K

• 3359k.pdf
• 5409K.pdf

CAB6: CIMREX and EXTER / E- and E1000 Series to PC/PC-Compatible. RS422

Allen-Bradley ControlLogix to CIMREX and EXTER / E- and E1000 series
B&R 2000 series (Mininet) to CIMREX and EXTER / E- and E1000 series
PC to CIMREX and EXTER / E- and E1000 series
Siemens Simatic S7-300/400 to CIMREX and EXTER / E- and E1000 series

• 3307s.pdf

CAB20: Siemens S7-200 to CIMREX and EXTER / E- and E1000 Series. RS422

• 4480s.pdf

03339: Idec Micro to CIMREX and EXTER / E- and E1000 Series. RS232

• 3339k.pdf

03338: Idec Micro to CIMREX and EXTER / E- and E1000 Series via CAB8. Screw Connectors. RS422

• 3338k.pdf

03337: Idec Micro to CIMREX and EXTER / E- and E1000 Series via CAB8. RS422

• 3337k.pdf

03334: Toshiba PROSEC T-Series to CIMREX and EXTER / E- and E1000 Series with CAB12. RS232

• 3334k.pdf

03342: Koyo DL-Series to CIMREX and EXTER / E- and E1000 Series with CAB12. DB9 to DB15. RS232

• 3342K.pdf

03333: Toshiba PROSEC T-Series to CIMREX and EXTER /E- and E1000 Series. RS422

• 3333k.pdf

03332: Control Techniques Unidrive to CIMREX and EXTER / E- and E1000 Series Point-to-Point. RS422

• 3332k.pdf

03331: Control Techniques Unidrive to CIMREX and EXTER / E- and E1000 Series. RS422

• 3331k.pdf

03330: Control Techniques Unidrive to CIMREX and EXTER / E- and E1000 Series via CAB8. RS422

• 3330k.pdf

03343: Koyo DL-Series to CIMREX and EXTER /E- and E1000 Series with CAB12. RJ12 to DB9F. RS232

• 3343k.pdf

05005: Communication Ports EXTER / E1000 Series

Communication ports drawing

• 5005S.pdf

03341: Atlas Copco DMC to CIMREX and EXTER /E- and E1000 Series. RS422

• 3341k.pdf

03349: Matsushita FP3 to CIMREX and EXTER / E- and E1000 Series. RS422

• 3349k.pdf

03344: Koyo DL-Series to CIMREX and EXTER / E- and E1000 Series. DB25 to DB15. RS422

• 3344k.pdf

05273: Cable Adapter for CIMREX and EXTER / E- and E1000 Series to Old Cable Assembly for MAC50/90/200. RS422

• 5273K.pdf

05238: Moeller PS4-Series to EXTER / E1000 Series. RS232

• 5238K.pdf

05237: Mitsubishi AJ71QC24 to EXTER / E1000 Series. RS232

• 5237K.pdf

05236: Mitsubishi A1SJ71C24-R2 or A1SJ71QC24 or A1SJ71UC24-R2 or QJ71QC24 to EXTER / E1000 Series. RS232

• 5236K.pdf

05235: Matsushita FP1 to EXTER / E1000 Series. DB9M to DB9F. RS232

• 5235K.pdf

05239: Printer to EXTER / E1000 Series. DB9F to DB25M. RS232

• 5239K.pdf

05230: Koyo DL-Series to EXTER / E1000 Series. RS232

• 5230K.pdf

05210: Telemecanique TSX Nano/Micro/Premium to EXTER / E1000 Series. RS485

• 5210K.pdf

05234: Koyo DL-Series (RJ12) to EXTER / E1000 Series

• 5234K.pdf

CAB25: Shielded 24 V DC Supply Cable to CIMREX and EXTER / E- and E1000 Series

• 702K.pdf

CAB30: Programming Cable EXTER / E1000 Series. RS232

Allen-Bradley ControlLogix / SLC 5 / SLC 500 to EXTER / E1000 series
B+R 2000 series (Mininet) to EXTER / E1000 series
Mitsubishi FX1N/FX2N-232BD to EXTER / E1000 series
PC to EXTER / E1000 series ("Programming cable")
Siemens S7-300/400 to EXTER / E1000 series

• 5400K.pdf

CAB23: Extra RS422 Cable Between CIMREX and EXTER / E- and E1000 Series to CAB15. RS422

• 4353k1.pdf

05240: Siemens SIMATIC S5 to EXTER / E1000 Series

• 5240K.pdf

05241: Toshiba PROSEC T-Series to EXTER / E1000 Series. RS232

• 5241K.pdf

05252: Control Techniques Unidrive to EXTER / E1000 Series. RS485

• 5252K.pdf

05251: Festo/Beck IPC/FEC to EXTER / E1000 Series. RS232

• 5251K.pdf

05250: Festo/Beck IPC/FEC RJ Connector to EXTER / E1000 Series. RS232

• 5250K.pdf

05246: Intelligent Actuator SuperSEL to EXTER / E1000 Series. Centronics25 to DB9F. RS232

• 5246K.pdf

05245: Keyence KV Series to EXTER / E1000 Series. RJ11 to DB9F. RS232

• 5245K.pdf

05243: SEW Eurodrive Movi ... to CIMREX and EXTER / E- and E1000 Series with CAB8. RS485

• 5243K.pdf

05242: SEW Eurodrive Movi ... to EXTER / E1000 Series. RS232

• 5242K.pdf

CAB34: Mitsubishi Q-CPU to EXTER / E1000 Series

• 5404K.pdf

CAB33: Matsushita FP0/M/2/2SH to EXTER / E1000 Series. RS232

• 5403K.pdf

CAB32: Omron C/CS1 to EXTER / E1000 Series. RS232

• 5402K.pdf

CAB31: Allen-Bradley Micrologix to EXTER / E1000 Series. RS232

• 5401K.pdf

CAB10: Allen-Bradley SLC5 and 500 to CIMREX and EXTER / E- and E1000 Series RS485 to RS422

• 3350s.pdf

CAB6 Cable assembly. E- and E1000-series to PC/PC-compatible port. RS-422 to RS-232

• 3307s.pdf

CAB9: CIMREX and EXTER / E- and E1000 Series to Unit with RJ45 Connector. RS422

CIMREX and EXTER / E- and E1000 series to Mitsubishi FR-A/E/F/S
CIMREX and EXTER / E- and E1000 series to Mitsubishi servo via MR-CN3 plug

• 3320s.pdf

05244: SEW Eurodrive Movi .... to EXTER / E1000 Series. RS485

• 5244K.pdf

CAB14 Cable assembly. Matsushita FPO/M/2/2SH to E-series or E1000-series with CAB12. RS-232

• 4790S.pdf

Cable assembly. Intelligent Actuator SuperSEL to E1000-series. Centronics25 to DB9F. RS-232, 05246K

• 5246K.pdf

CAB8 Adapter. E- and E1000-series to RS-485. RS-422 (4 wire) to RS-485 (2-wire)

• 3315s.pdf

05005 Communication ports E1000-series

• 5005S.pdf

05238 Cable assembly. Moeller PS4 series to E1000-series. RS-232

• 5238K.pdf

05235 Cable assembly Matsushita FP1 to E1000-seies. DB9M to DB9F. RS-232

• 5235K.pdf

CAB23 Cable assembly. Extra RS-422 cable between E- and E1000-series to CAB15. RS-422

• 4353k1.pdf

CAB15. CANopen adapter. E- and E1000-series RS-422 port to CANopen

• 4350K.pdf
• 4350s1.pdf

05243 Cable assembly. SEW Eurodrive Movi .. to E- and E1000-series with CAB8. RS-485 (2-wire)

• 5243K.pdf

05242 Cable assembly. SEW Eurodrive Movi ..... to E1000-series. RS-232

• 5242K.pdf

CAB32 Cable assembly. Omron C/CS1 to E1000-series. RS-232

• 5402K.pdf

CAB31 Cable assembly. Allen-Bradley Micrologix to E1000-series. RS-232

• 5401K.pdf

EXTER E1000 DoC CE, RoHS

• Copy of EXTER E1000 DoC CE, RoHS 2016 (PROD CERT - 1177191 - 1 - A1) - 1.PDF

ABS EXTER/E1000 Series Marine Certificate

ABS EXTER/E1000 series marine certificate

• ABS_EXTER_E1000_08-LD356481-1-PDA.pdf

Certificate of Compliance for EXTER and E1000 UL1604/508/60950-1

• EXTER_E1000_series_UL1604_508_60950_1_20080728_E207750.pdf

Germanischer Lloyd Marine Approval for EXTER/E1000 Series (new 2013)

• GL 44074 - 06HH EXTERE1000 (PROD CERT - 1016324 - 1 - A2) - 1.pdf

Trade compliance Exter- / E1000-series, PI00137

• EXTER_E100_PANEL800_series_EAR_G049136.pdf
• PI00137.pdf

Green Passport EXTER/ E1000

• Green Passport Declaration E1000 and EXTER (PROD CERT - 1021782 - 1 - A1) - 1.pdf

E1000 DNV Certification

​E1000 DNV Certification

• E1000 DNV TAA00000TY (PROD CERT - 1216979 - 1 - A1) - 1.PDF

EXTER E1000 ABS PDA Certification 14-LD356481-1-PDA (PROD CERT - 1032465 - 1 - A1) - 1

• EXTER E1000 ABS PDA Certification 14-LD356481-1-PDA (PROD CERT - 1032465 - 1 - A1) - 1.pdf

E1000 / Exter - Is it possible to use an USB mouse on keypad panels?

Is it possible to use an USB mouse on keypad panels?

Yes, and no. Yes you can connect a mouse to keypad panels and you can select object with it, but you cannot manouver objects using the mouse, this still needs to be done using the keypad.

E1000, Modbus master driver to Jokab Pluto (Safety PLC system)

Modbus addressering for example register 400.001 will give error message "Illegal function Station 1"
Driver Modbus Master version 5.05.19

Solution
Adjust driver parameter "Force function code 0x10" to Enable

E1000 printer Form feed

Adressing in E1000

• E1000_Adressing.pdf

E1000 heartbeat in firmware 1.5 and 1.31 (and older)

Do the Tx (timeout) and Rx (retries) commands work for EXTER / E1000?

Does EXTER or CIMREX series / E1000 or E-series withstand acetone vapour?

You can find information about how the operator panels reacts to different solvents in the installation manuals. Regarding acetone, we recommend that you do not install an EXTER or CIMREX / E1000 or E-series panel in an enviroment where it will be exposed to acetone vapour.

Supported voltage and power peaks for E1000/Exter teminals

How to get the old Index functionality in E1000

When upgrading a project from E-series to E1000-series there is a difference between the Index functionality.

For example if I1 = 1

E-series

D0.0I1 -> D1.0

D0I1 (Signed 32-bit) -> D1 (Signed 32-bit)

E1000-series

D0.0I1 -> D0.1

D0I1 (Signed 32-bit) -> D2 (Signed 32-bit)

There is a possibility to get the old E-series behaviour in E1000-series if the driver being used is a v5 (generic) driver or most of the MELSEC drivers.

To get the old functionality two driver commands XFLINDEX and XBITINDEX has to be set.

E1000 alarm list size

E1000: CAB7 no longer available

Since the CAB7 is no longer available, the current work around is to change controller port in your HMI project to COM2 (RS-232).

Use the converter 6ES5 734-1BD20 from Siemens to connect the CPU port on the controller and the HMI via a 25 to 9-pin converter.

Communicate with a Siemens IM 151-8 PN/DP (ET200S) using E1000

Use the S7 ISO over TCP/IP driver in E1000.

E1000: Load project to terminal from USB memory

E1000: Japanese characters

Customer uses  font MSSONG.TTF and tested DejaVu.TTF for Japanese characters, it looks good in the computer simulation but not on the E1032 panel.
 
ANSWER
Works in font "Arial Unicode MS" which indicates that MSSong and DejaVu does not contain the character set that the customer has used.
 
Note that font "Arial Unicode MS" (Arialuni.ttf) it is about 22MB big and can not be loaded to memory of an E1032, which is not possible to expand the memory!
The memory must be expanded to cope with this font. Since the E1032 can not be expanded, there must be a E1070 or higher. 
Tested in the E1070 with 64MB memory card, works ok!
 
Settings in E1070:

E1000 Index system signals etc.

Problem with CF memory card detection in Exter/E1000 panels

E1000 serien: ASCII-object and Unicode in E1000

E1000 pro+ Axis window white

E1000: Get the value 8224 in some registers when using Current Recipe register

E1000 and Siemens S7-1200

Is it possible to communicate to S7-1200 system with the E1000 terminals?

 Yes, but in the driver properties you need to change the slot number to "1"

The S7-1200 has only one communication port- Profinet or TCP(Iso on TCP). With the driver S7-ISO over TCP  the tests has been successful.

Internal memory card in E1000-series

How do you expand the memory capacity of a terminal E1000.
 
This is done by using a CompactFlash card (CF). To put this card in the terminal assigned as needed. On the circuit board inside the terminal cover on the back, there's a socket for inserting the CompactFlash card.
 
The project must also be set for an expanded internal memory expansion, meny selection Configuration - Terminal ...
Enter the size of the memory card, see picture below:

Set Clock in E1000

To set the operator panel clock in E1000, a maneuverable Date/Time object (Digital clock) must be defined.

The mode switch (service meny) have only function for Date/Time format.

Use two different VNC clients to the same E1000 panel

How to use two different VNC clients to the same E1000 panel?
It is impossible to use two Remote Access at the same time with terminal.
 

Solution
The E1000 terminal could work with two VNC clients (computers) one connected to the port 5800 in Remote Access, and the other one connected to port 5900 in web mode. Test made with E1071 and E-Designer project,  settings in Network Services.

E1000: Service menu, Load project to terminal

- From E-designer manual

2.7 Service Menu

The Service Menu is accessed by setting the mode switches on the operator panel in mode 1000. Please see the Hardware and Installation manual for the operator panel for information about the mode switches.

The following options are available in the Service Menu:

Network Settings
Select this option to access the Network Menu.

Network Menu
The options in the Network Menu corresponds to selecting Settings/Network in
E-Designer and contains the following items:

Erase Project Memory
This option erases the project memory.

Load Project from Memory Card
An empty operator panel can be started with an existing E-Designer project, used in
another panel. The project first has to be saved to a Compact Flash memory card or
USB memory stick via the function Save project to memory card (for example via a
function key).
Insert the memory card in the empty panel before boot-up. Then select Load project
from memory card in the service menu and follow the instructions.

Enter Transfer Mode
Allows entering transfer mode manually, needed to download projects via GSM
modem. See section Transfer via GSM Modem for details.
Not available for E1012 and E1022.

Enter Run Mode
Allows entering run mode manually, needed to download projects via GSM modem.
See section Transfer via GSM Modem for details.
Menu item Described in
TCP/IP Settings 18.2 Network Communication through Ethernet
Accounts 18.5 Network Accounts
Services 18.4 Network Services

Update System Program from Memory Card
Insert a Compact Flash or USB memory stick with a new system program and follow
the instructions. The system program can also be updated via the configuration tool
for the operator panels.
Calibrate Touch Screen
Follow the instructions on the screen to calibrate the touch screen.

23.5 Transfer to/from External Memory Card

Not available for E1012 and E1022.

Export Project to Memory Card

In order to export the project to a Compact Flash memory card or USB Flash drive,
select Transfer/Export Project Transfer File. The output from the export is a datfile.

Load Project from Memory Card

Save the dat-file to the library BACKUP/PROJECTS on the external memory card.
The file structure is automatically created when formatting the card in the operator panel. If no operator panel is available, the library structure must be created manually. A function or touch key can be configured in the configuration tool to download the
operator panel project, by selecting the function Loads project from memory card. See also chapter Function Keys.
The command MCI can be used to indicate that a memory card is used in the panel. Type MCIx on the Commands line by selecting Setup/System Signals. x represents the digital signal that will be set when a memory card is inserted.

________________________________________________________________________

How to read the project from USB

• USB memory into the terminal
• Switch 1:ON
• Power ON
• Select Load From memory Card - select project
• Power OFF (< 5sec)
• Switch 1: OFF
• Power ON
• The terminal start up and read the file and restart.

________________________________________________________________________

E1000 Password on USB key

E1000 OEM loader when using EEPROM

iX_EXTER_E1000_Environmental

• iX_EXTER_Environmental_PIEN144D.pdf
• iX_Mitsubishi_Environmental_PI00145C.pdf

PCN E1000 remove coating on CPU and Power board (PDM_CDOC - 1030026 - 1 - A1) - 1

• PCN E1000 remove coating on CPU and Power board (PDM_CDOC - 1030026 - 1 - A2) - 1.pdf

Release Notes EXTER/E1000 post 1.52 release

Release information about changes after the 1.52 release

PIEN173E includes the EXTER panels

PI00175E includes the E1000 panels

• PI00175E.pdf
• Release_Notes_EXTER_1_52_PIEN173E.pdf

Remote Access Viewer v1.5.4, for Exter/E1000 - TxA/TxB/TAxx - X2 panels

Remote Access Viewer is a program for remote access and control Exter/E1000 - TxA/TxB/TAxx - X2 panels.

It is possible to access, reflect and control panels from a PC by using the VNC client program, Remote Access Viewer (freeware), together with the built-in VNC server (Remote Access function) in the iX Panels.

NB: Even though the help file suggests another key combination, please note that Ctrl-Alt-Shift-F toggles Full screen mode on / off best, so you Restore from Fullscreen mode with this key combination! 

vncviewer.exe_patch.zip contains a patched vncviewer.exe

• MA00756.pdf
• RemoteAccessViewerSetup 1.5.4_iX.exe
• vncviewer.exe_patch.zip